Best Conditions for an Aerial Thermography Survey
Aerial thermography, sometimes called aerial infrared thermography, is the use of a drone-mounted infrared camera to measure the heat radiating from the ground, animals, buildings or equipment below. Done in the right conditions, it will find a pig in a sorghum crop from several hundred metres away, a wet patch under a roof membrane or a failing string on a solar array. Done at the wrong time of day, the same camera over the same paddock shows you nothing but sun-warmed dirt.
The conditions matter more than the camera, which is why this guide covers how a thermal survey is planned, what time of day suits each kind of job, and the conditions that should send you back to the shed.
How does aerial thermography work?
A thermal camera does not see temperature. It sees long-wave infrared energy leaving a surface and converts that into an apparent temperature. How much energy a surface emits depends on its real temperature and on its emissivity, which is how efficiently the material gives off heat. Skin, fur, vegetation, concrete and soil all have high emissivity. Bare polished metal has very low emissivity and mostly reflects what is around it, which is why a shiny roof can read as cold as the sky on a clear night.
The DJI Matrice 4T, the DJI thermal drone we sell and have flown on these jobs, uses a 640 x 512 uncooled sensor with a high-resolution mode up to 1280 x 1024 and a measurement range from minus 20 to 550°C across two gain modes. Sensitivity is not the problem. The problem is that everything under the drone is also absorbing and releasing the sun's heat on its own schedule, and that schedule is what decides when to fly.
Why time of day matters more than anything else
Two things happen every day that either help a thermal survey or wreck it, and both are driven by the sun.
Solar loading
From mid-morning, the sun heats soil, rock, roads, roofs and tree trunks. By mid-afternoon many of those surfaces are warmer than a cow, a pig or a person. On a Queensland summer day bare ground can pass 60°C. A 38°C animal is then a cold spot in a hot scene, and small animals disappear into the clutter entirely. Everything also radiates that stored heat for hours after sunset, so early evening is often worse than people expect.
Thermal crossover
Twice a day, usually around dawn and again in the early evening, the ground and the objects on it pass through the same temperature, and for anywhere from a few minutes to an hour contrast collapses. A thermal image taken during crossover looks like fog. The timing shifts with season, cloud and surface type, so you learn it for your own area instead of trusting a clock.
Put those together and the pattern is simple. For anything that makes its own heat, the best window is the coldest part of the night through to just before crossover at dawn. Ground temperature has bottomed out, the target is still warm, and contrast is at its peak. Research on drone-based animal detection has found the same thing. Morning flights recovered far more targets with far fewer false positives than mid-afternoon flights, because surfaces heated during the day were still radiating.
Best time of day by type of thermal survey
Livestock, feral pests and search and rescue: pre-dawn or night
Warm-blooded targets against cold ground. Fly from roughly two hours before sunrise until the sky starts to lighten, or through the night if you hold a night operations approval. This is how operators find pigs, deer and wild dogs with a DJI Matrice 4T, and it is the only practical way to check a mob of cattle for a downed animal across a big paddock in the dark. Cooler months give more contrast than summer because the ground drops further overnight.
Roofs and buildings: just after sunset
Here you want the sun's heat, but you want it leaving. Dry roofing cools quickly after sunset, while wet insulation and trapped moisture hold heat longer, so an hour or two after dark the wet areas glow warm against a cooling roof. Thermographers doing building work aim for that early-evening window and repeat the survey at the same time on a later date so the two can be compared.
Solar farms: middle of the day, full sun
This one is the opposite of every other job. A faulty cell, diode or string only shows as a hot spot when the panel is working hard, so you need high irradiance. The industry standard IEC 62446-3 sets a floor of 600 W/m² at the plane of the array, which in practice means clear skies from late morning to mid-afternoon. Steer clear of the glare angle near solar noon and fly on the calmest day you can get.
Irrigation, pipes and crop stress: early morning
Leaks, blocked lines and water-stressed plants show up best in the first hour or two after sunrise, once crossover has passed but before solar loading builds. Wet soil and transpiring leaves stay cooler than their surroundings as the day warms, and that gap is easiest to read early. Pair the thermal pass with a multispectral flight if you want to turn stress patches into a variable-rate map for your ground rig or spray drone.
Weather conditions that make or break the data
Wind. Above about 5 m/s, moving air strips heat from surfaces and smears the differences you are trying to measure. Solar inspections degrade badly past this point, and drones lose stability and battery life. Wait for a calm window.
Rain and wet ground. Water on a surface dominates its thermal signature and evaporative cooling flattens contrast. Wait until surfaces are dry, which after heavy rain can mean a day.
Cloud. Overcast skies reduce solar loading, which helps daytime animal work a little but ruins solar inspections and makes roof surveys inconsistent. Patchy cloud is the worst case because the scene changes under the drone mid-flight.
Humidity and haze. Moisture in the air absorbs infrared, so long-range detection suffers on humid coastal mornings and you either fly lower or accept a smaller search area.
Ambient temperature. Bigger gaps between target and background mean cleaner images. A cold winter night beats a warm summer one for anything living.
Record all of it. Ambient temperature, wind speed and direction, cloud cover and exact take-off time go in the log for every thermal flight, because without them two surveys of the same asset cannot be compared and any temperature reading is just a number.
Getting the camera settings right
Match the gain mode to the job. High gain gives precise temperatures across a narrow range, which suits animals and buildings, while low gain trades precision for a wider range and is the setting for fires and hot industrial equipment. On the Matrice 4T, switch on the high-resolution mode when you need to separate small temperature differences between objects.
Set emissivity for the surface you care about, or the temperatures will be wrong even if the picture looks fine. Choose a palette that suits the target. White hot or black hot work for search and detection, and a colour palette like ironbow suits inspection work where you want gradients to stand out. And keep enough overlap between images, around 70 to 80% for mapping work, so the software can stitch a usable thermal orthomosaic.
Height is a trade-off, since higher covers more ground per battery and lower puts more pixels on the target. For detection work a 640 x 512 sensor at 60 to 100 m above ground finds a pig-sized animal reliably, and for measuring a fault you get closer.
Who is allowed to fly a thermal survey in Australia?
Less paperwork than most people expect, at least in daylight. The Matrice 4T weighs under 2 kg, which puts it in CASA's sub-2 kg excluded category. You can fly it for work, on your own property or someone else's, without a Remote Pilot Licence or a Remote Operator Certificate, provided the aircraft is registered, you hold CASA's free RPA operator accreditation and you stay inside the standard operating conditions: daylight, within visual line of sight, below 120 m and clear of people, airports and controlled airspace.
Night flying is where the paperwork starts. It requires an ReOC with a night approval, and flying beyond or extended visual line of sight requires a CASA approval and endorsement on top. Since the best window for animals is before dawn, that approval is worth having if pest or livestock work is the main reason you are buying. Australian Agricultural Drones holds CASA ReOC no. 9011 with night and extended visual line of sight approval, so when we set up a Matrice 4T for a customer we know what the paperwork looks like from the inside.
If you want the gear on your own property, the DJI Matrice 4T product page covers what the drone does and what it costs, and we can point you to CASA-approved training if you decide to go for the licence. If you would rather someone else flew the survey, we can put you in touch with a contractor who does.
Thinking about a thermal drone for your property? Call 0448 158 563 or email info@ausagdrones.com.au and we will talk through the Matrice 4T and the right window for your kind of job.
Frequently Asked Questions
What is the best time of day for a thermal drone survey of livestock?
The two hours before sunrise, or through the night if the operator holds an ReOC with a night approval. Ground temperature is at its lowest and animals are still warm, so a cow, pig or dog stands out sharply against the paddock. Avoid the half hour either side of dawn when ground and animals pass through the same temperature and contrast disappears.
Can aerial thermography find a lost pet or a missing person?
Yes, and it is one of the most common reasons people buy a Matrice 4T. A thermal drone flown at night or pre-dawn picks up a warm body against cool ground from hundreds of metres away, then the zoom camera confirms what it is. Success depends on getting airborne quickly and on conditions, since heavy rain, thick canopy and hot afternoon ground all make detection harder.
How windy is too windy for aerial thermography?
Around 5 m/s, or about 18 km/h, is where thermal data starts to degrade noticeably. Wind strips heat from surfaces and evens out the temperature differences you are trying to see, and it costs the drone stability and battery life. The DJI Matrice 4T is rated to fly in more than that, but experienced operators reschedule survey work and wait for cleaner data.
Can a thermal drone see through trees or into buildings?
No. Thermal cameras only read the temperature of the surface they are looking at, so dense canopy hides an animal underneath it, although gaps in the canopy and the animal moving into the open often give it away. A camera sees a roof surface and not the room below, but moisture trapped in the roof changes how that surface cools, which is what a roof survey reads.
Do I need a licence to fly a DJI Matrice 4T for thermal work?
Not for daytime work within visual line of sight. The Matrice 4T is under 2 kg, so it sits in CASA's excluded category and can be flown commercially with aircraft registration and the free RPA operator accreditation. You need an ReOC with a night approval to fly it at night, and a CASA approval and endorsement to fly beyond or extended visual line of sight.
Planning a thermal survey for pests, livestock, a roof or a solar array? Call 0448 158 563 or email info@ausagdrones.com.au. We will help you choose the right thermal drone, or connect you with a contractor who can fly the job at the right time rather than the convenient one.



